View previous topic :: View next topic |
Author |
Message |
Lodi Winching Ollie
Joined: 27 Aug 2008 Posts: 95 City: Lodi
|
Posted: Sep 21, 2008 6:31 pm Post subject: Gearing Issues!! HELP NEEDED!! |
|
|
Ok so we have a 12 tooth tav 2 right now, with 60 tooth sprocket an our inside diameter of our spool is approximately 5 inches. We have a Briggs 6.5 intek ohv engine. We tried slide starting today,and also dock starting,but we had no luck,it has plenty of power to pull us through water but not enough speed to keep us on top of the water ,but like i said it can pull us through the water,like nothing...just really slow. I was wondering why no one makes the sprocket smaller like say i went down to a 50 tooth or something. Just wondering... also open to any suggestions |
|
Back to top |
|
|
|
Mario C Frontside 180
Joined: 18 Oct 2006 Posts: 451 City: Lakeville
|
Posted: Sep 21, 2008 6:35 pm Post subject: |
|
|
i run a 6hp, 12t tav2, 62 tooth sprocket, 8 inch dia. spool with 1200ft. amsteel
deepwaterstarts 190 lbs no prob and is even a bit too fast full throttle. _________________ www.devotid.com
www.lasewer.com |
|
Back to top |
|
|
Lodi Winching Ollie
Joined: 27 Aug 2008 Posts: 95 City: Lodi
|
Posted: Sep 21, 2008 6:37 pm Post subject: |
|
|
Instead of redoing our entire spool to make it 8 inch dia...coudlnt we just make sprocket smaller? Just wondering |
|
Back to top |
|
|
JeffKnox Backside 180
Joined: 09 Apr 2007 Posts: 2044 City: Jacksonville/Gainesville
|
Posted: Sep 21, 2008 6:47 pm Post subject: |
|
|
Lodi Winching, no.... if you leave the small spool and decrease the sprocket you lose all your torque....
it needs to be between 6 and 8 inch inner diameter spool and a sprocket between 54 and 72 _________________ PAVT since '05/'06 |
|
Back to top |
|
|
key Frontside 180
Joined: 30 Jul 2008 Posts: 349 City: south brazil
|
Posted: Sep 25, 2008 11:14 am Post subject: |
|
|
ive said before but will ask again. ive seen what you recommend JEFFKNOX,.....but what will be going on with my current spool?? aproximate 4.5 inside diameter with 1000 foot with 9.0 motor, 12 tav, 68 rear. i have several different size sprokets to play with. im just wanting to know is it neccessary to trash this spool?? or give it a shot? |
|
Back to top |
|
|
key Frontside 180
Joined: 30 Jul 2008 Posts: 349 City: south brazil
|
Posted: Sep 25, 2008 11:14 am Post subject: |
|
|
ive said before but will ask again. ive seen what you recommend JEFFKNOX,.....but what will be going on with my current spool?? aproximate 4.5 inside diameter with 1000 foot with 9.0 motor, 12 tav, 68 rear. i have several different size sprokets to play with. im just wanting to know is it neccessary to trash this spool?? or give it a shot? |
|
Back to top |
|
|
Montgomery Backside 180
Joined: 26 Feb 2008 Posts: 976 City: Rogers
|
Posted: Sep 26, 2008 9:02 am Post subject: |
|
|
im running an 8hp/TAV2 setup with 8t/60t sprockets 8.5" i/d spool w/ 600' of rope _________________ Go Balls Deep Or Go Home |
|
Back to top |
|
|
paulmc Frontside 180
Joined: 27 Nov 2007 Posts: 292 City: Manchester, UK
|
Posted: Sep 26, 2008 10:52 am Post subject: |
|
|
key & lordi, increase your inner spool diameters.
i run 6.5 TAV 10t/68t with 7" inner, deep waters no problems!! does get a lil quick at the top end, i would consider going down to a 60 or 62 tooth sprocket, but she works so why brake her!!!! |
|
Back to top |
|
|
key Frontside 180
Joined: 30 Jul 2008 Posts: 349 City: south brazil
|
Posted: Sep 26, 2008 12:22 pm Post subject: |
|
|
i guess what im getting at, is what result am i going to get from this spool?? too fast of a pull? not able to deep water start? |
|
Back to top |
|
|
dalesk8 Backside 180
Joined: 03 May 2007 Posts: 719 City: South OZ
|
Posted: Sep 26, 2008 4:57 pm Post subject: |
|
|
paulmc wrote: | key & lordi, increase your inner spool diameters. |
change your spool I.D to 8 inches. |
|
Back to top |
|
|
Montgomery Backside 180
Joined: 26 Feb 2008 Posts: 976 City: Rogers
|
Posted: Sep 26, 2008 5:06 pm Post subject: |
|
|
key, changing your spool i/d is basically like changing the size of one of your sprockets it will either add speed or torque depending on if you go bigger or smaller _________________ Go Balls Deep Or Go Home |
|
Back to top |
|
|
Pulldozer Faceplant
Joined: 02 Feb 2006 Posts: 38 City: Redding, Lake Shasta
|
Posted: Sep 26, 2008 8:25 pm Post subject: |
|
|
Lodi,
Did you take your governor off of the motor?
if not that may be your problem also. _________________ Pulldozer Winch Systems
Hand built by riders for riders
EMAIL - pulldozerwinch@yahoo.com
WEBSITE - pulldozer.com |
|
Back to top |
|
|
|
|